arterial Posted January 24, 2005 Report Share Posted January 24, 2005 After a bit of a lay off I am trying to get back into PTE. I have a big project on which will be made much easier with the new lightbox facility in PTE but I can not get v4.31 to run.I have run v4.14 with out problem but having upgraded to v4.31 the programme crashes with the error message "APR caused a general protection fault in module V128IID.DRV at 002:00009492". I am running the programme under W98SE on a Dell Dimension XPS R450. I have made sure the audio and video drivers are the most current versions but to no avail. I can still run v4.14 OK. Does anyone have any suggestions? Thanks in anticipationArterial Quote Link to comment Share on other sites More sharing options...
ccmanz Posted January 24, 2005 Report Share Posted January 24, 2005 This is not much help. But until you get better help.Have you tried downloading and installing the v4.31 again? Quote Link to comment Share on other sites More sharing options...
boxig Posted January 24, 2005 Report Share Posted January 24, 2005 I could be wrong but I think the problem is in your video card driver. If you sure you have the updated drivers then try to use the Hardware Acceleration not on "Full" and see if it will solve the problem. Quote Link to comment Share on other sites More sharing options...
Igor Posted January 24, 2005 Report Share Posted January 24, 2005 I just sent you test file, please let me know about result.We've received one more two similar reports since August. Probably some rare configurations under Windows 98 can't correctly work with simultaneous threads (loading of pictures of previews) of the new interface in v4.30 Quote Link to comment Share on other sites More sharing options...
Conflow Posted January 24, 2005 Report Share Posted January 24, 2005 '98 Crashes with PTE431Igor,This may be of some help to the New Member. We had the same problem with 2 of our '98 PC here in our Workshop. Sometimes both PC's "Froze" and sometimes the "General Protection Fault"was involked. In both cases we traced the 'fault' to the Win '98 Op.System. Win '98 does not like 2 Copies of the same Program on the PC, ie:- An "old" version and a "new" version on the PC 'Start Menu'.Probably1) The Member is opening and using the "new" PTE 431 version - Registered on the Start Menu.2) The Member also has the "Old" version PTE 414 (NOT IN USE) but Registered on the Start Menu3) Nearly all versions of Win '98 will "fault" sometime under these conditions.In our cases we created 2 Folders for PTE,viz:- PTE-414 and PTE-431 - Then we removed the "old" PTE-414 version from the Start Menu. This solved our problem.To do this:- RH.Clk on the bottom Screen Toolbar-->select 'Properties'-->select 'Start Menu'-->select 'Remove'. In the open window search for the "old" verson of PTE and remove it.Sometimes its not 'Listed' there, in this case the "new" version has probably been installed in the "old" Program Folder - best thing is to remove it and re-name the "old" Folder then re-install the "new" version in a New Folder as described above...... Win '98 now see's 2 different Programs.This is a 'shot in the dark' but in our cases it was the problem. It's nothing to do with PTE rather its a case of "Fooling '98" - and as we all know Win '98 always kicks for touchdown.Regards,Brian.Conflow. Quote Link to comment Share on other sites More sharing options...
arterial Posted January 25, 2005 Author Report Share Posted January 25, 2005 Bingo.Your suggestion worked a treat.Thanks Brian and thanks to Igor for his personal reply.It's great to be back using PTE, congratulations on a fantastic piece of software and an an amazingly useful Forum.All the best.Alistair (Arterial) Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.